delete

Que faire en cas de fuite?

Lorsqu’une fuite survient dans une maison, la situation peut très facilement dégénérer et mener à des moments très critiques. Généralement, appeler votre plombier sera nécessaire afin de tout remettre en état et d’être sûr que la fuite ne recommencera pas. Cependant, il existe bien des choses à faire pour limiter les dégâts et éviter l’inondation totale de votre logement avant l’arrivée du professionnel.

Tout d’abord, la première chose à faire et loin d’être des moindres, c’est de couper le courant d’électricité. On y pense pas toujours, mais lors d’une fuite, il y a souvent des projections d’eau qui peuvent engendrer des dégâts conséquents sur vos meubles ou vos appareils électroménager, et cela peut devenir dangereux. Les appareils électroménagers en contact avec de l’eau peuvent créer un court-circuit ou même une électrocution. Pensez également à ouvrir vos fenêtres, cela permettra un séchage plus rapide de la pièce. N’oubliez pas de protéger vos objets de valeur avec des bâches par exemple, pour éviter tout contact avec l’eau.

Une fois tout cela fait, vous pouvez essayer de stopper la dispersion d’eau dans les pièces. Il suffit d’enrouler un chiffon imbibeur ou une serpillière à l’endroit de la fuite, puis placer une bassine ou un seau pour récupérer l’eau qui s’éparpille. Cela vous permettra de limiter fortement les dégâts causés par la fuite le temps d’obtenir une vraie solution.

Ensuite, il vous faudra trouver le robinet général d’arrivée d’eau et de couper l’eau directement à la source. En général, ce robinet est situé à côté du compteur d’eau, si vous êtes en appartement. Si vous vivez dans une maison ou une habitation individuelle, le robinet d’arrivée d’eau peut se trouver à l’extérieur de la maison, dans le jardin, sous un couvercle de béton dans le sol. S’il est à l’intérieur, il sera certainement près de vos toilettes ou de l’évier de cuisine. Pour couper ce robinet, tournez-le dans le sens des aiguilles d’une montre.

La troisième étape sera de tenter une réparation de la fuite vous-même. Cela peut ne pas être très compliqué, en fonction évidemment de l’endroit et de la grosseur de la fuite. Il est tout d’abord impératif d’en trouver la cause : une fuite provient forcément d’une installation de plomberie. Vous pouvez essayer de remonter en suivant les tuyaux jusqu’à trouver l’endroit où il y a eu un problème. Identifiez ensuite le matériel avec lequel à été fait le tuyau. Est-ce un problème avec le raccord ? Ou le tuyau est-il endommagé ?

Si la fuite provient du raccord, serrez les fixations au maximum, ou remplacez le joint. Si le tuyau est percé, vous pouvez trouver des produits anti-fuite sur le marché, qui seront une solution temporaire mais acceptable. Avant d’utiliser le produit anti-fuite, videz les tuyaux et nettoyez-les à l’aide d’une brosse pour enlever la rouille, l’oxydation ou la graisse.

Si tout cela n’a pas suffi à complètement stopper la fuite, vous devrez passer à la dernière étape : appeler un professionnel de la plomberie ! Pour bien choisir votre plombier, comparez bien toutes les informations que vous trouverez, demandez conseil autour de vous. Et surtout, assurez-vous que le plombier que vous aurez choisi est en possession d’une assurance responsabilité. En effet, la réparation de votre plomberie peut causer d’autres dégâts dont vous n’êtes pas responsables. Évidemment, n’hésitez pas à bien expliquer votre problème au préalable, ainsi que les réparations que vous avez potentiellement prodigué par vous-même. Demandez toujours à avoir la facture en main propre, c’est une assurance pour vous en cas de problème futur. Lors de la réparation, portez attention aux outils que le plombier utilise, et prenez garde à ce qu’il protège votre sol. Si tout ceci se passe bien, alors vous pouvez être sûrs de la fiabilité de l’artisan !

delete

Useful Materials and Tools in Plumbing

The plumbing system in your home is an important aspect of your home. It plays a crucial role to help maintain the condition and efficiency of your home. If you are planning to repair something in your plumbing system, click here. Well, to help you, here are some useful materials and tools for plumbing projects. 

Plumbing

    Sink Auger 

A sign auger is considered as one of the most valuable of the different tools for plumbing that you will surely want to have in your toolbox. For breaking and clearing clogs in tubs and sinks, this is a very easy to use a tool. This is not advisable to be used on toilets because toilets require a special tool called closet auger or toilet auger. 

With a steel auger bit on the end, the sink auger consists of a flexible cable. The cable is coined within a drum canister and extends to the drain for it to be able to reach the clog and remove it. As the drum is turned, the cable, as well as the auger, also turns.  A thumbscrew is what locks the cable and the canister. 

    Closet Auger 

To clear clogs in the toilet, a toilet auger is used. Sink augers are designed for a different process so it is not advisable to use it in the toilet or vice versa.  

    Flange Plunger 

To clear clogs in the toilet, the flange plunger or ball plunger is specially designed. It works by applying vacuum as well as the force of water. Unlike a standard cup shaped plunger which is usually used for sinks and tubs, the shape of this plunger seals the hole at the bottom of a toilet bowl. 

    Cup Plunger 

Probably the most common special plumbing tool in your home is the cup plunger. It is used to clear clogs in sinks, showers, and tubs since it has a rubber cup-like shape and handles. This is not advisable for clearing toilet clogs since that will require a flange plunger. 

    Plumber’s Tape 

This is an important material to prevent leakage at threaded plumbing joint connections. To effectively seal pipe threads being joined together for plumbing purposes, such as threaded water connections of water lines and shower heads, you can use a plumber’s tape that is versatile, inexpensive, and common. 

    Adjustable Pipe Wrench 

The quintessential metal plumbing tool is the adjustable pipe wrench. This tool is an iconic symbol of plumbing repair. Tremendous leverage and grip are what this tool provides. It is designed to grip round objects securely by getting its sharp serrated teeth into the pipe which increases pressure as the wrench is turned once you tighten the wrench around the pipe with the use of the knurled knob. 

    Faucet Valve Seat Wrench 

To remove the valve seats on a compression faucet so that it is possible to be replaced, you will need a faucet valve seat wrench. The oldest style of faucet is compression faucets. Against a valve seat in the faucet body, they work by compressing a nylon or rubber washer in the end part of the brass stem down. 

delete

Tips on How to Drain a Toilet 

Draining a toilet seems to be a simple thing to do but it is quite tricky. If the toilet is stopped up or not, the method for how to drain a toilet is completely different. It may also be a good reason to remove it if the toilet is stopped up. To clear the blockage or run a snake, many people will remove the toilet.  

Drain a Toilet

You can rotate the toilet upside down and remove anything that may block or lodged them. It is difficult to remove unless you drain it first when the toilet is stopped up. Replacing your toilet with a new fixture is another reason to drain a toilet.  

Since you will need to get all the water out before you carry it through your house, it is essential that the toilet is drained before removing it. Depending on the situation, stopped up or not some methods will work better.  

However, if you are not confident enough to do this job, you can always ask assistance from plumbing companies such as Plombier Montréal that offers professional plumbing services and guarantees customer satisfaction at all times.  

Well if you think you can do this job without assistance from professional plumber then here are some tips on how to drain a toilet that will surely help you. 

     Plunge Out The Water 

Whether it is stopped or not, it is true that plunging is a great way to remove the water from the toilet bowl. Because of the plunging motion, the water is pushed out of the toilet bowl and down the drain. By turning off the stop valve to the water supply for the toilet, you can shut the water off.  

You can then slowly flush the water from the tank to the bowl and dip to remove that water all way out of the toilet bowl before removing the toilet. 

    Siphon Out The Water 

To siphon out the water from the tank or bowl, a short hose can be used. You can do this by completely filling up the hose with water then plunge one end with your thumb. The next thing that you will is to drop the other end into the toilet bowl then get the hose lower than the bowl and release your thumb. 

As long as you keep your end lower compared to the bowl, it will begin draining and will do so. You must remember that if the toilet is stopped up, this will not work so well. 

    Bail Out The Water 

To bail out the water out of a toilet bowl, you can use a small cup or small bowl. In order to get the majority of the water out of the bowl, a small cup or even the cap of a hairspray bottle or paint container will do. 

    Sponge Out The Water 

To remove all of the water from a toilet, using a good sponge is a great way. The sponge can remove all the water from the trap since it can easily fit around everything in the tank and can also fit way down into the bowl. 

delete

Basic Types of Pipes Used in Plumbing

Since you have a choice of several kinds of pipe, doing your own plumbing can be quite a confusing experience. You will have a hard time to choose because they can blend together. When the choice was limited to galvanized pipe or galvanized pipe, the answer isn’t a clear as it may have been in the past few years. Here are the types of pipes that can be found at home. 

Plumbing 

PEX  

This is found in supply lines and suitable to be done even if without the help of professionals. This type of pipe is flexible; color coded and has truly delivered water supply plumbing. PEX is simple to join and easy to cut. It yields to logic since it can make 90-degree curves with ease. Plumbing supply lines with PEX is easy for most homeowners. 

    PVC- Polyvinyl Chloride 

Found in drain and vent lines. Because it is lighter and much easier to work compared to traditional galvanized steel pipes, PVC pipe has been a very big deal in the industry of plumbing for the last few decades. 

For drain or waste pipes, as well as stacks, you will generally be using PVC pipe. Because it requires little more than a hacksaw, miter box, and solvents which will eventually stick the pipe together, this makes it very easy to install. 

On the white surface of the pipe, the diameters are clearly marked. Diameter can be determined using a sizing tool such as Pi-piper if you are not able to easily read the mark. 

    Rigid Copper 

Mainly found in supply lines and is also known as the water supply pipe. Using a hacksaw or a special tube cutter, you can easily cut this type of pipe. As it requires a practiced hand to solder copper together, a connection is a different matter. Because it does that carry the health risk that PVS has, a rigid copper pipe is great for water supply. 

ABS 

Except that it is black, this pipe looks exactly like PVC pipes. It is often not allowed anymore by plumbing codes because it is the older version of PVC. Just like PVC, it is also used to drain vent and drain pipes. The best thing that you can do is to replace with PVC if you are working with ABS. 

    Flexible Copper Tubing 

For short runs, flexible copper is used. In tight spots, you can see it leading up to your water heater or for cold water supply. Using a hacksaw, you can easily cut a flexible copper tube and bent to fit around the corners of your home. Flexible copper tubing is not recommended for exterior use because it cannot stand up well to extreme temperatures.  

    Galvanized Steel 

The pipe of popular imagination is the galvanized steel. When you think of a plumbing, it is the pipe that comes into your mind. With each end of the pipe threaded, it is made of galvanized steel. Using connecting joints, individual pipes are screwed into each other.